Filters for LS MT225HE

So, my dealer came up with an LS MT225HE, from somewhere. I've read that it's recommended to replace oil, HST, & Hydraulic filters @ 50 hours. So, I'm starting now gathering info as to which filters to buy.

After using the LS brand part numbers, then crossing them over to popular brands, I've come up with some oil filter choices. There are several Wix/NAPA filters that should fit. The NAPA 1356 & 1357 are a little longer than the original, which should be good. All the specs look the same...

Read more

Filters for LS MT225HE

RTVX 1100C K connect PTO will not engage

OK, this sh!t is starting to get old. After the second storm this season (this one the big blizzard that hit the northeast) that I have not been able to use my RTVX with connect snow blower I’m starting to feel a little ripped off. Let’s face it, probably could have bought a hell of a snowblower for the $33,000 I spent on this set up. After getting my rig back from the dealer after a month to fix a broken u joint (apparently a problem Kubota was well aware of when they sold me the set up in...

Read more

RTVX 1100C K connect PTO will not engage

Factory installed accessory wiring and light bar question

I am installing front and rear nilight light bars onto my dads Kubota RTV-X1100c that has cab and factory installed wiring already set up. We purchased the Kubota switches with the five wire connection that easily plugs into the connectors in the front inside roof. We installed the front light bar, and switch and it turns on and works well. When we did the identical set up for the rear light, it doesn’t work. The rear light switch has power since it has a little light on it, and we tested...

Read more

Factory installed accessory wiring and light bar question

massey 3070 4x4 w/cab

anyone tell me some do's and donts with a 3070 i am looking at buying one and i am not to familiar with this vintage it is 4x4 with loader and cab i am unsure where tolook for possible issues or problems any help would be greatly appreciated thanks

massey 3070 4x4 w/cab

Massey Ferguson 1030 no electrical power?

My tractor, battery was struggling to turn over , I place a battery charger on it over night. Next day no electrical power. No horn ,lights anything. Figured battery dead
, Replaced it. Still no power. Have also replaced ignition switch with no change , any ideas?.
Thank you.

Massey Ferguson 1030 no electrical power?

New RTV Break-In

So I have a question I hope the experts here can answer. I took delivery of my new X1140 and had it delivered about 3 miles from my home where I had a heated warehouse to install the options I had waiting for it. When completed I drove it home. I didn't really think too much about break-in, I just drove it and it did great averaging about 23mph on a cold day after being warm from the warehouse and then also letting the engine warm up before I started the drive.

When I got home I grabbed...

Read more

New RTV Break-In

Headlight Assembly for Kioti CK25, 27, 30, & 35, 2004-2014

Looking for KIOTI Tractor T2185-69517BB Head Lamp Assembly for CK25 27, 30, 35 model tractors, built between about 2004-2014.

There's a new one on Ebay for about $350.

I live in North central Louisiana. Anybody know of a tractor salvage yard in the mid-South that might have some of these Kioti models with a decent assembly ?

How 'bout a better price on a new assembly ?

Headlight Assembly for Kioti CK25, 27, 30, & 35, 2004-2014

2014 RTV X1100C will not move. Hydraulic Oil foaming, HST? Transmission?

Hi All.

I just purchased a used RTV that I want to fix up. It was not taken care of well at all so I know I have lots to do but I want get the basics working first. I don't know anything about these machines so I really need help The engine works well but the problem is it just wont move when put into gear. symptoms are...

-Axles barely spin when in gear and so slow that if I grab ahold of it with my hand it will stop.
-Axles don't increase speed very much when accelerated
-Hydraulic fill...

Read more

2014 RTV X1100C will not move. Hydraulic Oil foaming, HST? Transmission?

Helimod mirror ext./Kubota/curtis skid shoe.

Did the helimod mirror extension to my grote mirrors they work great.Kubota/curtis snow plow skid shoes SUCK.The pic is after (1) snow plowing on a 1/8 mile gravel drive.It burnt the skids down to nothing.Made a mod and installed Meyers skid shoes 100% better.s

Helimod mirror ext./Kubota/curtis skid shoe.

RTV-X110C Going Slow

HI Guys.
Our X1100C has started to go slow.... The engine sounds like its revving freely but running on flat ground we only get to about 30km/h (18mph). All oil's are clean and at correct levels, Filters have been changed including fuel filter but nothing seems to be making a difference.
The one thing i have noticed is that the VHT Pressure relief rod is sticking out (just) past the 21.5mm spec in the operators manual and is touching the cam. I'm wondering if it could be releasing pressure...

Read more

RTV-X110C Going Slow

DEF on LS Tractor

I'm about to buy a new tractor. Was wanting an LS MT225HE, which is the same as a NH Workmaster 25.

My local dealer has had LS tractors ordered for month's & can't get one.

But, I've found another dealer who has an LS MT235HE in stock, for a good price. BUT, as ya'll know, it has the DEF system. I have never used a tractor with that system.

BUT, I've read only BAD things about it. So, for some of you guys who know, what would be the downside, or the "cons", if you will, of buying the 235...

Read more

DEF on LS Tractor

LS MT225HE

Since the NH Workmaster 25 & the LS MT225HE appear to be exactly the same tractor, this looks like a good forum for this post.

My wife wants to get a tractor with a hydra trans, so she can use it more. Our Kioti CK27 has a man trans with shuttle.

The Kioti has done everything we've needed a tractor to do & done it well. For that reason, I looked 1st at the Kioti models. BUT, I eliminated them, because of the brake pedal location. It's not as bad as some, but still requires picking your...

Read more

LS MT225HE

Boomer 50 Hydro

Hello to all. I have a 2013 New Holland Boomer 50 with 180 hrs on it.
I bought it used. I have lots of power in 1st and 2nd range I can spin all 4 tires with the loader and 400 lbs of ballast in both ranges.

My issue is that in 3rd (high) range its it is week, it will stall out on even small grades. The engine will drop 2-300 rpm, throw a smoke haze and it will stop moving. It does not make any difference if I partially or fully press the hydro pedal.

Does any one have a Boomer 40 or 50...

Read more

Boomer 50 Hydro

2011 900xt rearend?

Guys, i just replaced rear halfshafts both sides, on my machine and was wondering if the axel is lifted off the floor and the trans is in neutral ,i spin 1 tire forward and the other side should go backwards easily is this correct?spider gears does this i think,but seems like a lot of drag to turn the tire, What am i missing? Thanks for any help,Scotty

2011 900xt rearend?

X1140 Delivered!

Friday I received the call I had been waiting for since December 18th when I signed the quote, my X1140 was ready for delivery! I finished a couple of meetings and canceled one and then headed to the Dealership. The machine checked out and after writing a very large check the X1140 was scheduled for delivery that afternoon. I asked the dealer to deliver to my work where I have a heated warehouse so I could install a few of my accessories. I took my time installing accessories this weekend...

Read more

X1140 Delivered!

X Series Plastic Bed Side Panel Removal

Does anyone have a how-to on removing the plastic side panel on the bed of the X-Series RTV? It probably isn't too difficult, however, I would prefer to not learn the hard way and damage the panel if at all possible. I took delivery of my new X1140 and everything is great except when dumping the bed when in single row configuration, the back side panel on the drivers side gets a terrible vibration to it and it is just annoying. I would like to remove it, inspect and reinstall to see if I...

Read more

X Series Plastic Bed Side Panel Removal

X900 steering controller

Has anyone had their steering control unit start leaking hydraulic fluid from around the shaft where steering wheel mounts? I was wondering if anyone has able to replace the seal vs buying a new unit for $730.

X900 steering controller

I need an RTV-X100C chainsaw tool box

I need an RTV-X100C chainsaw tool box . I have built a a wooden box to carry my chainsaw, gasoline, oil, and a few misc tools. I carry it in the bed and it keeps the contents in place very well. However when I fill the rest of the bed with firewood I am not able to dump it without sending my tools into the wood pile. I would like to use the whole bed to haul firewood. I would love to hear some ideas about how others are carrying their chainsaw and tools. I am sure I am not the only one with...

Read more

I need an RTV-X100C chainsaw tool box

Rear Wheel Bearings.

I have a 2017 RTVX1100C with 4000m (6300kms). Recently rotated the tires and found a small bit of play in the rear wheel bearings. Is this normal or with the mileage should I plan on replacing these soon. Also, are they complete hub assemblies or pressed in style bearings?
Thanks
Jim

Rear Wheel Bearings.

Clone app Development company

Omninos Solution is one of the best https://omninos.com/app-development-clone-app/ & service provider companies that use the finest mobile app clone scripts to provide robust and precise app clones to their clients. Talk to our expert developers and business executives at Omninos and discuss your app clone requirements.

Clone app Development company

String Trimmer Mount

Have enjoyed the discussions on this forum. I have had a BX-23 TLB for a number of years and decided to buy an RTV X900.

Dealer tells me my unit will arrive the last week in August. I don't want to put a full rack on my machine but would like to put something on the bed that would hold my string trimmer. I can weld something up or purchase just not sure of the best design that would be easy to put on and take off of my machine. Any pics or recommended web sites would be appreciated.

String Trimmer Mount

First Snow Plowing Experience With X900

We got about 8 inches of snow overnight so I got my first experience plowing snow with my X900. Our neighborhood has about a half mile of paved road on a mountain ridge so there are few flat areas and one very steep hill. I have plowed it many times using my Kubota BX23 tractor with a back blade. I only had a 4 foot scrape blade on the tractor so it took a long time to clear the road and by the time I was finished my neck and back were in considerable pain from turning backwards for...

Read more

First Snow Plowing Experience With X900

X1100c Snowblower alignment rattle height

I purchased a ‘20 x1100c with k-connect plus snowblower and am looking for some owner feed back on pto noise. With hand throttle all the way up and pto engaged I can lift the blower to about 4” off the ground (maybe 1/4-1/3 the way up) before the shaft gets noisy. It’s not a horrible noise but just when you hear it go from smooth operating to that first audible difference where you say that’s as far as I want to raise it. Does that sound normal or do other owners get more angle/height out of...

Read more

X1100c Snowblower alignment rattle height

Planning stages for new garage. Steel vs pole barn vs traditional build

I'm considering adding a 3 stall garage next fall or depending on cost might be spring of 2023.

I looked at one a friend just built, 40x50 steel, fully insulated. He bought it in 2020 but just finished it up. Cost back then was 20k for materials. 13k for the concrete. Very nice building.

Not sure steel can work for what I want. I don't have room for 40' deep for all 3 stalls. I'm looking at 40' deep for one stall and the other 2 stalls would be 30' deep. A telephone poll, underground...

Read more

Planning stages for new garage. Steel vs pole barn vs traditional build

Dealing with ice on the road instead of sanding

I have over a mile of dirt road to keep open, and while plowing is easy, it is the ice coatings we get from time to time that is much more of a problem. I don't maintain a large supply of sand under cover or salted so I have to sand the road by hand - having a sander come in costs over $100 each time! To reduce the need for sanding I use a DR Power Equipment grader. https://www.drpower.com/Power-Equipment/Power-Graders/DR-Power-Grader-/p/PG21148XXN

I use this in all the other...

Read more

Dealing with ice on the road instead of sanding

New Install of Boss UTV Power V-XT

On my new RTV X1100C I had the dealer install a Boss UTV Power V-XT plow. I had one on my previous X900 and loved it. The new RTV has a beefed-up bumper and I like the improvements - on my X900 the bumper snapped on two spots so the new configuration is superior. However, the additional framing gets in the way of drilling for the electric connection bracket. Because of this problem the installer just used zip ties to secure it to the large tube of the bumper...

Read more

New Install of Boss UTV Power V-XT

Burn up the calories from that same food

Burn up the calories from that same food. If you're a thin person, you're
Derma RX Cream
Derma RX Cream
Derma RX Cream
Derma RX Cream
Derma RX Cream
Derma RX Cream
Derma RX Cream
Derma RX Cream
probably on the lucky side of a lot of those, if not all of those. You're probably on the side that makes it easy to resist food, makes it easy to burn calories, makes it easy to remain thin. If you're a fat person, if you're an obese person...

Read more

Burn up the calories from that same food

adidas superstar femme

Qui ont récemment adidas superstar femme blanche (et exclusivement) révélé les Stan Marsh Stan Smiths, vous auriez tous supposé que les versions d'accompagnement pour Kyle, Kenny et Cartman arriveraient également bientôt - et vous devinez bien, avec les trois personnages apparaissant aujourd'hui à titre officiel images adidas. Ici, nous avons un autre premier aperçu entre ma superstar «Kyle» de South Park x adidas - et comme vous vous en doutez, elle arrive parée des fringues de...

Read more

adidas superstar femme

buty adidas męskie

Yohji Yamamoto ma skłonność buty adidas męskie accomplish przesuwania granic tego, gdzie może iść obuwie lifestylowe, często tworząc sylwetki, jakie są zarówno awangardowe, jak i modne. Japoński projektant mody ma wyjątkową umiejętność łączenia światów współczesnego designu z nowoczesną technologią obuwniczą i właśnie to zrobił w swoim zupełnie nowym adidas Y-3 IDOSO IMPROVE. Z punktu widzenia palety, buty są zaprojektowane camaro dyskretnym, neutralnym tony, draught beer piękno tkwi w...

Read more

buty adidas męskie

converse one star

Vorig jaar bracht Carhartt's lifestyle-gerichte divisie, WIP, zijn zware invloed naar een verzameling Nike-iconen. En voor 2019 willen ze hun samenwerking met het merk Beaverton voortzetten en een suv de meest iconische silhouetten van Nike's dochteronderneming Chat, de Chuck 70, aannemen. Het zwart-witte duo suv Chuck 70s komt found converse classic chucks aanbieding waterdicht GORE-TEX-bovenwerk, GORE- TEX zij- en hielbranding, tonale All-Star-logo's gedrukt op dom mediale enkel en...

Read more

converse one star

converse schuhe günstig sale

Pass away Sneaker-Produktion hat sich within den letzten Jahren dramatisch verändert und neue, einiger schädliche Herstellungsmethoden in großem Umfang eingeführt. Diese Woche wird die Initiative „Renew“ von Converse mit Upcycling-Paaren des klassischen Chuck seventy in leuchtenden Frühlingsfarben fortgesetzt. converse schuhe günstig sale Das Nachhaltigkeitsprogramm von Communicate hat seit seiner Einführung im letzten Herbst ausnehmend Aufmerksamkeit auf sich gezogen und die...

Read more

converse schuhe günstig sale

First time snowblower use

One word description , WOW!!!!!!
Previously I used a blade mounted to my jeep to do this work . I have a concrete driveway about 50' wide by about 150' long . The blade worked fine except I had to make repeated passes because of the length I had to push it to . I Was lucky I had an open field to push it to behind my property . The blade would only keep so much in front of before spilling off to the sides , so I had to make many passes over the same area to move it to the field . I...

Read more

First time snowblower use

Roxor Bumpers and early TJYJ Jeep Bumpers

I've read that with * slight modifications* the early 87-06 TJ/YJ Bumpers will fit on the Roxors. I've found these on sale and with free shipping so will probably get the front and rear on the way. If I made one, it would not look nearly this good . I'll let ya'll know how it works out. bordercollie...

Read more

Roxor Bumpers and early TJYJ Jeep Bumpers

RTV X100C LIGHTS

Has anyone installed a LED bar light on top of the x1100 using OEM wiring with any issues such as wattage cause I am wanting to put a light bar on mine and I am not sure if I can use a 30" 300w light bar

RTV X100C LIGHTS

simple wiring for bx 2200

hoping some one can provide a simple wiring diagram so tractor will start and shut down and have oil pressure , water temp and voltage gauge. don't need anything else.. no safety switches lights etc.

simple wiring for bx 2200

RTV-X1140 LED light install

Installed Nilight LEDs + Nilight wiring harnesses (they include relays, fuses, and rocker switches) on the RTV over the holidays. For power, I ran a dedicated 12ga DC positive wire directly from the positive battery terminal. No new holes were drilled anywhere on the RTV for the install (well, except to mount the dc positive terminal to the inner fender under the hood). I used t-brackets from Lowes for the rear light mounts and "modified" Simpson strong tie mounts (also from Lowes) for the...

Read more

RTV-X1140 LED light install

Heated and Cooled Seat cover for my RTV

Hey guys, Just wanted to brag about this.. lol
Wife bought me a heated and cooled seat cover/cushion while back., Never used it as my pickup already has heated seats.,
Came across it doing some closet cleanouts the other day .. So thought hell, I will put it in my X1100c..
Ahhhh man,, That booger fit pretty nice.. Heats VERY Well and cools pretty good too.
Now I got Heat and Cooled seat in the RTV !!! What a deal ! said it was only like 50 bux .
Has a couple of little pockets that hang off...

Read more

Heated and Cooled Seat cover for my RTV

Here's a "Talk About Anything" - 2021 - 22 edition

This is just like the old one, talk about whatever.
The other thread is getting a bit too large so we'll use this one going forward.
The other will remain but this new one should reduce overhead and load times.

Here's a "Talk About Anything" - 2021 - 22 edition

RTV X1100C Passenger Seat Back Removal

Stupid question time. When installing my seat covers couldn't figure out how to remove said item to secure the cover with the velcro strips...and there is no access behind it. When I installed my hitch extension/skid I looked at it again before leaving and still couldn't figure it out...but only spent a few minutes because it got cold real quick. Parts catalog "vaguely" shows 1 or 2 bolts securing it, but I just couldn't find them. Do I have to remove the interior back panel to access...

Read more

RTV X1100C Passenger Seat Back Removal

UTV Hitchworks Receiver Extension/Skid Plate and Transmission Plate

This one's for you TechJunkie...and anyone else interested.

This afternoon I stopped by work to install the Hitchworks UTV-XECP kit and was pleasantly surprised how easy it was. The quality is excellent and they even included the extra hardware needed for the later Model 2020 and up RTV-X900, x1100, x1120 and x1140. My X1100CW was mfg late 2017 so this was not needed and I and can't comment as it applies. Only needed 3 metric sockets, an extension, a ratchet...and a mallet to bust loose...

Read more

UTV Hitchworks Receiver Extension/Skid Plate and Transmission Plate

First Plow With RTV1100

Finally got to try it out. Only got this pic, as I had to drive it when plowing, LOL Impressions:

Heater will melt you in cab.

Not a lot of snow yet, but it rained and froze first, so driveway is glare ice on the gravel. You couldn't walk on it. Then got a layer of wet snow that froze. Then it snowed last couple days, but 70 KPH winds have blown most of it away.
I did have to do some counter steering and pedal the throttle when I made a full width pass UP the driveway. It doesn't look like...

Read more

First Plow With RTV1100

Hand Throttle Question

Can someone tell me why the manual for the 1100C states not to use the hand throttle while driving the vehicle? Also, what is the difference in the optional hand throttle kit that Messicks sells as apposed to the pull up type on the 1100C?
Would there be any issue setting the pull throttle to half speed while plowing snow?

Hand Throttle Question