Mahinda m force 105

lundi 28 février 2022

I am trying to find diagnostic code reader. I have def. I have no power, no light to regenerate. no rpm past 1500 rpm and get check engine light. I have had it in 2 dealer repair with them telling me nothing. very poor service. I am on my own for repair so must find and fix my self. thanks


Mahinda m force 105

RTV900 Alternator Upgrade

Need Bigger Alternator. I have a SnowDogg plow on my 2009 RTV 900. I plow my driveway and 2 door yards with it and frequently am changing the plow setup, not just raising and lowering it. After I have plowed, the next morning, if it is cold, say 10ºF, I have to put the batter charger on it to get it started. I thought the battery might be going bad, but then thought about how much power was being used to run the plow system. Yes, the belt on the alternator is tight and not slipping. Is there...

Read more


RTV900 Alternator Upgrade

Toolmans gun rack

samedi 26 février 2022

Just installed my gun rack from toolman and it is exactly what I was hoping for. Thanks again Tim!


Toolmans gun rack

Arg not my day, -20f and my x1100c

It starts (or in this case, not) with it -20f and a no start.


Pay attention, it is a bit in R, so...

That night the heat lamp slips and melts hole on battery.

While removing the old battery, it clips the bottom and dumps 1/2 cup of acid into my lap.
(That slippery soap feel, is actually you being emulsified)

Bought new HD start/deep cycle, had to replace ground, due to post being in front side of battery. (More convenient anyhow) replaced with 1 gage 24".

-2 Pairs of...

Read more


Arg not my day, -20f and my x1100c

RTV_X1100C Mirrors

vendredi 25 février 2022

So I'm thinking of ordering the outside rear view mirrors for my 1100C. Just so I have better view down the sides when I am snow plowing.

Are they any good and can they be folded in or removed when I am trail riding in the bush?


RTV_X1100C Mirrors

1985-86 YANMAR 276D w/ YANMAR front loader for sale

Up for sale is a YANMAR 276D with OEM YANMAR loader. Tractor is a low hour tractor that was purchased as a basket case.
New OEM correct engine with roughly 15-20 hours on it. Tractor runs and operates with no issues almost like new. No leaks, tight and strong.
Also have OEM YANMAR Owners, Parts and Repair manuals that go with tractor along with receipts. Manuals are in great condition and a small fortune in themselves.
Bought new OEM parts when found and available, no...

Read more


1985-86 YANMAR 276D w/ YANMAR front loader for sale

x1100c door seals

My x1100c door seals are torn dealer wants $100.00 per door anyone find a suitable replacement right now I am searching Steele products catalog


x1100c door seals

50 hour filter change on X1100C

jeudi 24 février 2022

I just performed the required 50 hour filter change on the hydraulic system and transmission of my new machine. As I experienced before with my X900 the hydraulic filter (suction) on my X1100C was incredibly tight. It took all my strength and patience to get it loose! It was very tight until at least after one full turn. Anyway, I was curious to see how much metal can be seen in filter so I removed the canister and examined the paper pleating. Nothing is visible and a magnet turned up...

Read more


50 hour filter change on X1100C

x1100 cargo bed

lundi 21 février 2022

I recently saw a video for the RTV 850 and wondered if the box plate for the 850 would fit on the 1100. Attached is a print out of the box plate assembly for the 850


x1100 cargo bed

290 pound hog taken in Leakey, Texas

:wow: It's a big un.

290# hog taken in Leakey, TX


290poundHog.jpg


290 pound hog taken in Leakey, Texas

Interesting Dodge truck

I just had this vid Emailed to me & thought some might find it interesting . :tiphat: Bob

http://www.youtube.com/watch?v=1XUEvkMZHno


Interesting Dodge truck

Mahindra XTV

Anybody stepped into one of these?

Sorta, kinda looking for a RTV and the offering are awesome. First thought was just go with a Kubota but after some searching there is a lot to offer now day. What I'm liking is some offer 27" wheels with a couple more inches of travel namely the Mahindra and Honda, that said I'm thinking stick with diesel.

I'm now an agent for a few gas wells that have to be addressed bi-monthly and a couple are in remote areas. Right now a pickup ain't getting there...

Read more


Mahindra XTV

Ordered a Windshield Yesterday :)

At one time, I wanted to make my own windshield in order to save $$. Then though, I started pricing the good Lexan and it was really up in price.
Then, I found this hard coat windshield and it was on sale for less than $275 delivered including tax.
What I've read about the hardcoat looked promising so yes, I ordered it ! I'll let ya'll know how it works-stay tuned.. https://www.sidebysidestuff.com/emp...ted-full-front-windshield-mahindra-roxor.html...

Read more


Ordered a Windshield Yesterday :)

New fellow here.

I picked up a 2019 Roxor with winch, plastic winshield and roof. Traded in a poloris ACE and a honda pioneer. Would do it again for sure. Since I have built a cab with a cj windshield and rollbar. Has suicide doors that are removable in seconds. Put military markings and tires on and chipped the engine. Cruises easily at 60mph 2000rpm. So glad I made the change. Drive mine almost daily using about a tankfull a month.
If you are looking at a sxs, get a roxor and don't look back...

Read more


New fellow here.

moose plow x1100

samedi 19 février 2022

I purchased at auction yesterday a RM4 72" quick mount Moose plow It appears Moose does not make a mount for my RTV x1100c, anyone adapt this plow to their RTV?


moose plow x1100

Backup Camera

jeudi 17 février 2022

I have been planning on installing a backup camera for some time because of my lack of depth perception when trying to maneuver my machine in tight spaces. After bumping trailer hitch to trailer hitch with my truck I finally ordered a camera from Amazon and installed it yesterday. I mounted the camera on top of the transmission using a 6" bolt that attached to the camera mount and an existing bolt hole on the transmission. The monitor was mounted on the dash. Total installation time was...

Read more


Backup Camera

Tires for a New RTV 1100C

mercredi 16 février 2022

I currently have a 2014 1100C. I have a new machine coming later this week. When I purchased the one in '14 I had asked for a recommendation for tires for show plowing. I'm pretty sure it was here or one other site. I have Rocktane XD tires and ITP wheels on the machine that's here but would like to get a better tire for snow plowing. Recommendations on a good place to buy?


Tires for a New RTV 1100C

No power steering pump whines

2010 1100 rtv moisture was In tank drain and refilled a couple of times to clean fluid and still power steering works on and off and dump bed jerky up and down pump whines all the time more when turning or using bed any ideas would be appreciated.
Thank you


No power steering pump whines

again probably for about a day before they go bad And in

again probably for about a day before they go bad And in doing that you start to Keto Trim extract more and more of the compounds from the mate leaf that increased GLP So it's kind of cool You can kind of get an increased effect So what I'll typically do is make a about to ounces and just sip it throughout the day and I do.

https://nutradiary.com/keto-trim/


again probably for about a day before they go bad And in

x1100c front drive shaft removal

lundi 14 février 2022

well i gave up and ordered a new front driveshaft now i can't figure out how to remove it i took out the center crossmember thinking i could get it low enough to slide it out the back no luck .it looks to me like i might have to remove or unbolt the front diff and lift it up then bring it out the front looking for suggestions


x1100c front drive shaft removal

rtvx900g

Hi just wondering if you can pull apart your rear axle and change your bearings.RTV x900g
ThankYou Kevin


rtvx900g

Winch Recommendations

Hi Forum Members
I would really appreciate some guidance and recommendations on purchasing a winch for my 2017 1100C. Need it mainly for my new snowblower but need advice on hooking up, ease of use , strength , etc.


Winch Recommendations

dude hey I'm the AOL guy no you're not goodbye for

dude hey I'm the AOL guy no you're not goodbye for Brandi for Mike none of the audio from you coming up and talking to us is gonna be in this right hmm yeah maybe yeah so spoiler alert yeah Mike looked directed this oh who
Alpha Gro
Alpha Gro
Alpha Gro
won that part sorry Brandi you being by like five seconds okay and they're gonna they're gonna eat pizza tonight yeah all right let's see what they say so far coach Hey look it looks about...

Read more


dude hey I'm the AOL guy no you're not goodbye for

snow blower

samedi 12 février 2022

I have a x1100c thinking about a snow blower but I don't want to spend a ton of money on a k connect system I am thinking about taking a used walk behind snow blower and mounting the engine directlly on the blower and mount the assembly to the rtv. Another possibility is take the same blower and mount a hydraulic motor to it. Has anyone out there done any thing like this?


snow blower

What is the Lufthansa Name Correction Policy?

vendredi 11 février 2022

Before we intrude into the principal discussion, let’s share some studies about the airline itself. Headquartered in Cologne, Germany, Lufthansa name Change policy is one of the most favorite names in the aeronautics sphere. It's known for offering world- class air services to guestsglobally.Further, the carrier, with a number of accessories, is the largest airline in Europe. It was incorporated in 1953 and presently serving guests across over 220 domestic and transnational...

Read more


What is the Lufthansa Name Correction Policy?

RTV X1100C front cv joint broke

jeudi 10 février 2022

I have a 2018 RTV X1100C with about 300 hours on it and the front CV joint snapped. I'm surprised it failed so quickly with the only hard use is plowing snow. I see on youtube there are some videos on the older RTV 900's that require three bolts to be removed at the front differential. The X1100C doesn't have these bolts and it looks like the axle just pulls out once removed from the hub.

Can anyone verify this?

Thanks


RTV X1100C front cv joint broke

25 psi charge pressure

mercredi 9 février 2022

Hi everybody. Been lurking on here for a little while, and want to say thanks for all the help that's been provided. I've been able to find a ton of information on past threads; hopefully I'm not posting a question that I just could've searched for.

Little back story: 2015 RTV X900, doesn't move at all. I bought it from a guy for $2500 knowing this, and also noticing that there was ATF in the transmission and in the hydraulic tank. He took it to the dealer and they told him it would need a...

Read more


25 psi charge pressure

RTV 1100 rear u-joint source

mardi 8 février 2022

Does anyone have an aftermarket source for rear driveshaft u-joints for an rtv1100? Kubota prices are insane.


RTV 1100 rear u-joint source

RTV x1100 leaking steering controller

I thought it best to start a new thread so it will be easier to search in the future. I purchased a 2013 Kubota RTV X1100 in December of last year. I recently noticed the Hydraulic Steering Controller (orbital valve) was leaking through the input shaft seal. Kubota does not sell a seal kit, in fact you have to purchase the complete valve assembly at approximately $800. The valve is made by Sauer Danfoss in Poland. After some searching I found that Midwest Steering in Independence MO...

Read more


RTV x1100 leaking steering controller

Kioti Pricing Questions

dimanche 6 février 2022

A dealer is considering my proposal to take our used Kioti in trade, on a new CK2610HST.

I just went online & saw where there is up to $3100 rebates on CK models, thru Feb 28.

So, exactly how much is the rebate on the CK2610HST model ?

Is this rebate something I will get from Kioti, automatically, AFTER I buy, or is it something a dealer can just lie about & say they have already figured that rebate in with the price they offer ?

Also, I saw online that Kioti gives a $150 rebate to...

Read more


Kioti Pricing Questions

Honda 1000 vs Kubota X900

Seems both plow about the same .They both share the same blade.But i will take the Honda shifts so much better plowing snow.Power seems close plowing snow.I dont think the honda is faster then the kubota plowing snow.


Honda 1000 vs Kubota X900

My massy ferguson 10

I have a massy ferguson 10 garden tractor I was wondering if I can make a snow blade for it


My massy ferguson 10

Starting issues got me stumped!

vendredi 4 février 2022

First off The problem rtv is a 2014 x1100c,and has not given one hint of any trouble

until this cold snap we are presently in. Around Christmas day the rtv was tried to be

started, it was given the glow cycle and then turned to start no click or anything

happened. I thought the battery first and checked the voltage and it was 12.6 so the

next day same thing happened again when the rtv was tried to start. next the battery

was removed and load tested and checked good. Re-tried again...

Read more


Starting issues got me stumped!

2009 Kioti CK27 in North Louisiana

mercredi 2 février 2022

I bought new in '09. Has just over 600 hours. Just did the regular hundred hour oil & filter change.

Has a loader & new 5' County Line brand bush hog.

Hardest work it's done is mowing our 10 acres or so, that used to be a hay field, with a 5' bush hog.

Fill the pot holes in our 1/2 mile road/driveway, with the loader.

Pushed some downed trees & limbs off my wife's horse riding trails.

Has a few minor problems, but is ready to work, now. Only reason for selling is because the wife wants...

Read more


2009 Kioti CK27 in North Louisiana

Much Easier Shifting on new 1100C

I only have 32 hours on my 1100C but I am really impressed with the much easier shifting on this machine compared to my 2014 X900 when it was new. When not plowing 90% of the time I can shift easily - most times without even pressing on the brake! When plowing there is still the problem of having pressure on the system and there is a need to drop the plow a bit or gun the engine to make it easier to shift into reverse. Given that there are only 32 hours on the machine, I think by the end...

Read more


Much Easier Shifting on new 1100C

Tailgate Rattle

I love the simplicity of the tailgate latch system on the RTV's - It would be nice to have one latch to work rather than two - but the simplicity of the present system is nice in that it won't break or fail over time. BUT, on my new machine there is a slight rattle when it is closed. The slot for the latch pin is just slightly larger than the pin so when the gate is closed the entire gate moves about an eighth of an inch back and forth. While not a terrible annoyance there is an easy...

Read more


Tailgate Rattle

X1100C AC & Front Fan Cycles too Often

My Kubota RTV cycles the AC compressor and front cooling fan very frequently (approximately every 8-10 seconds). It seems to me this would shorten the life of the AC compressor clutch and the front cooling fan. I replaced the temperature sensor in the thermostat housing plus the fan relay under the seat. Wasted my time and money cause it made no difference. My dealer tech and the Kubota rep said this is a built-in Kubota design. I'm wondering: Do any of you have this issue?


X1100C AC & Front Fan Cycles too Often