Der er tale om div. årgange - ingen 2014 numre. Sendes ikke. Afh. ved Haderslev
Først til mølle.
Tlf. 22773814
Først til mølle.
Tlf. 22773814
10 numre af Modelflyvenyt bortgives
Brain trust help
I have the 1100 - 2013- 170 hours. running in south texas so it is 103+ degrees and dusty. will run a ways fine then temp gauge sneaks up. not in red but running a little hot. If I stop and idle, the temp goes down.
I spray the radiator coils off with water to get dust out. Any ideas on what is causing this? thermostat? thanks
I spray the radiator coils off with water to get dust out. Any ideas on what is causing this? thermostat? thanks
Brain trust help
Motor dummy til cub
Jeg søger en motor dummy/ cylindre og topstykker til min cub.
Det er en Bud Nosen 1:3,8
Det behøver ikke at være 100% skala så 1:4 er fint ;-)
Det er en Bud Nosen 1:3,8
Det behøver ikke at være 100% skala så 1:4 er fint ;-)
Motor dummy til cub
MDS 218 Pro Aero ( ring )
Hej. har en ny MDS 218 Pro Aero ( ring ) 36, 3 CM 3, kan ikke finde den hos Ripmax det står i papierne den kommer derfra det er ca. 3-4 år siden den er købt . mvh. Jan Linnebjerg 7441 Bording Airport DK. :):)
MDS 218 Pro Aero ( ring )
Trouble adding Diverter/selector/isolator on MF 135
samedi 23 août 2014
Hello,
I've been reading the forums and gaining knowledge on my family's MF135 that my grandpa bought new in 1967. I've been using it for years for light duty work around the farm, but it has never had auxiliary hydraulics. I've recently acquired a 3 point hitch forklift with a three spool control and have been looking forward to installing the necessary hardware to use it. I bought the often mentioned selector valve VFD1104 to replace the 180908M1-cover plate. When I went to replace the pieces this weekend I ran into an issue - the cover plate would not come off... The two bolts came loose and the plate will spin (until it hits a nearby nut), but it will not come off. I have not pried on it as excess force without knowledge goes against my better judgment, but I am at a loss and looking for suggestions.
I do not currently have a service manual but my brother in law intends to send me one when he gets a chance.
Any thoughts/suggestions/experience with this?
Thanks,
John
I've been reading the forums and gaining knowledge on my family's MF135 that my grandpa bought new in 1967. I've been using it for years for light duty work around the farm, but it has never had auxiliary hydraulics. I've recently acquired a 3 point hitch forklift with a three spool control and have been looking forward to installing the necessary hardware to use it. I bought the often mentioned selector valve VFD1104 to replace the 180908M1-cover plate. When I went to replace the pieces this weekend I ran into an issue - the cover plate would not come off... The two bolts came loose and the plate will spin (until it hits a nearby nut), but it will not come off. I have not pried on it as excess force without knowledge goes against my better judgment, but I am at a loss and looking for suggestions.
I do not currently have a service manual but my brother in law intends to send me one when he gets a chance.
Any thoughts/suggestions/experience with this?
Thanks,
John
Trouble adding Diverter/selector/isolator on MF 135
Electro uhu
Har arvet et gammelt halvfærdigt byggesæt nogen der kender den og kan det betale sig at lave den færdig eller er det til lossepladsen
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
Electro uhu
Inscription à :
Articles (Atom)
