2014 rtv 1100 wont go faster than 15 mphr.

lundi 27 février 2023

Hello everyone, just want to say thanks in advance as already see the amount of knowledge that is here using the search function.

With that said I did search a lot, but I was unable to really get a clear idea of where to start. I have a 2014 rtv 1100. I have owned this unit for about 18 months. I purchased it used. It has about 4300 hours. It was well loved by a local city. Ever since I purchased it used it has never really got anywhere near the advertised 25 mphr. It maxes out about 15...

Read more


2014 rtv 1100 wont go faster than 15 mphr.

Will the rear bumper from an RTV 900 fit an RTV X900?

Hi.

I would like to fit a rear bumper to an RTV X900.

Does anyone know whether a used bumper, removed from an RTV 900, would fit?

Thanks.


Will the rear bumper from an RTV 900 fit an RTV X900?

Rear axle questions

dimanche 26 février 2023

2008 Rtv 1100
I got rear axle bearing at the wheel hub that is in pretty bad shape, the wsm says I need to remove the whole axle subframe. For those of you who've done this job before, is it possible to remove the axle and bearings with the subframe still in place?
Next question, has anyone found a replacement boot for these rear axles? I need 1 to cover the splined section. I can't find it anywhere on the parts diagram.

Thanks much


Rear axle questions

Mahindra 2660

Anyone have a 2660 with loader? I bought one a couple of months ago and have found it to be very unstable. I am going to have the dealer install fluid in both rear tires and I have ordered 3in. wheel spacers to widen the rear tires a total of 6in. The tractor is to tall and narrow to be used on ANY uneven surfaces, plus the loaders on these tractors are so strong and will lift so much weight it makes it a dangerous combination. I have operated tractors for 55 years and this is the 1st one...

Read more


Mahindra 2660

Why UDT2 in the hydraulic (only) system

vendredi 24 février 2023

With the cost of UDT2 im asking why I'm running it in the hydraulic system of the RTV? I completely understand when it comes to the transmission but for a basic pump and 3 (with plow) cylinders I just don't get it. I'm new to the RTV scene so I'm asking questions before I make a mistake. My machine is a 2008 1100 if that matters.


Why UDT2 in the hydraulic (only) system

RTV 1100 and X1100 doors

mercredi 22 février 2023

The drivers side door on my X1100 has become increasingly difficult to open from the inside. So today I decided to see what the problem was. While I didn't see any thing obviously wrong with the mechanism I did notice some surface rust at the bottom of the door by the weep holes. Additionally I have seen quite a few 1100's for sale wit the bottom of the doors ate up with rust. Does any one have a good way to keed the doors from rusting out? I did spray a ton of fluid film down there...

Read more


RTV 1100 and X1100 doors

RTV-X900 Hydrostat making metal.

Thanks in advance for the help. I have a RTV-X900 that quit moving and has metal in the tank and in the filters. I have not pulled it apart yet but have been reading a lot on the forum. I was looking for some advice before I get started. Who makes a reasonable hydraulics test kit that fits Kubota and hopefully John Deere skid steers. What are the recommended procedures to flush the rest of the hydraulic system of debris? Any gotchas I should be aware off, flying spring to the eye, etc.. I...

Read more


RTV-X900 Hydrostat making metal.

RTV Maintenance Schedule Chart

For easy reference ...


GENERAL CHECK POINTS MAINTENANCE TABLE:​

Please note: this table is generic for all Kubota products. We recommend that you consult the Operator's Manual for information on your specific model.


RTV Maintenance Schedule Chart
Check Points Hour Meter Reading:
Check or Change Every Interval Shown Below
After
Purchase

Floor an wheel wells done! But.....question?

dimanche 19 février 2023

Hello again all,I know everyone loves pics so below a couple on my floor an fender wells I made.The floor i made out of alluminum so no more issues,an the wheel wells are galvanized steel.then zinc primed,an then sprayed 4 coats of truck bed liner on them.the chasis I ended up making with box tubing as factory was..then primed,an used por 15 on entire rtv.then I also sprayed truck bed coating on it as well.once it all dried I drilled 1/4 inch access holes in front tube chasis,an also on box...

Read more


Floor an wheel wells done! But.....question?

bobcat shifts hard

samedi 18 février 2023

just got a brand new bobcat uv34xl and it shifts hard. how do i fix that? new to the side by side world ..


bobcat shifts hard

RTV-X Maintenance

vendredi 17 février 2023

When rebuilding my kubota X1100 all the suspension grease fitting were dryer than a pop corn fart. Upon disassembly i could'nt find any indication that they had ever been greased. After replacing all the bushings and bolts I decided to make a maintenance chart. I found in the owners manual that Kubota recommends greasing the fittings every 50 hours. Does everyone grease every 50 hours? If not then how often?


RTV-X Maintenance

fuel cut ff valve

jeudi 16 février 2023

Immensly stupid question -- I cant get my FD20 to start --- went in search of a fuel cut off valve in the injector - but see nothing obvious

Not obvious on wiring diagram - so WHAT STOPS THE TRACTOR WHEN I TURN THE KEY?? -- valve ligter calble was coiled up behind dash since before I had it --- I have also a random wirenot connected to starter switch that appears something to do with the glow plugs so dont know where to attach - it although glowplugs seem to work ok with out it!


fuel cut ff valve

Heres my dovetail cabin i have been building in maine

lundi 13 février 2023

Its all dovetail an post an beam.did it all by myself just got it dried in finally, finished floor soon,an this is my full time permanent home,no grid at all.its on a mountain I purchased for my retirement.happy to answer any questions.20221103_173315.jpg


Heres my dovetail cabin i have been building in maine

X1100C Hand Throttle

Exciting times.... My Kubota dealer called today and my X1100c is here after a short wait for availability. I took it for a test drive and the salesman gave me a pretty good introduction. I'm having some LED work lights, a back screen, window tint and a cruise control installed so I wait just a little longer for delivery. After leaving today I realized that I didn't quite understand what the hand throttle is useful for. I didn't even think that came standard but the salesman said it does on...

Read more


X1100C Hand Throttle

40B industrial grills

Looking to purchase lower and upper grills for a 40B industrial.
New ot used


40B industrial grills

Please Consider Donating in Support of Net Tractor Talk

samedi 11 février 2023

Please Consider Donating
Hey guys and gals, it's that time again. Here I am with hat in hand.

This is the one time each year I ask for help with forum costs.

If you enjoy the forums and can afford to donate to help with forum expenses I would sure appreciate your show of support.

And I have a couple new items to show a token of my appreciation to those who donate.

Please consider parting with a little cash in support of the forums.

Site Supporters groups are as follows:

GOLD Site...

Read more


Please Consider Donating in Support of Net Tractor Talk

10% off udt2 at coleman

Just posting in case anyone needs hydro oil right now, coleman online has a deal where you can get 10% off oil sold by the case, 12 quarts, or 2x2.5 gallon, etc. Just posting to help out other RTVers.


10% off udt2 at coleman

Questions from the new guy

So, in an other thread, I posted about trying to help out a farmer in my town with his rtv 900.
Had some success, however, I have a couple of questions.
1 . Is there a difference between the 900 and 1100?
2. When I search for parts, sites will ask about the model. I see designation codes (W, G, R, etc) I have no clue what that means.
3. Is there a way to decipher the part number? Some numbers have k then a number, also a 2 digit number dropped in the middle of the thing.
4. Is it a secret...

Read more


Questions from the new guy

2014 Kubota RTV-X1120d parts forsale

I have completely stripped down my Rtv ton of parts available. Complete working harness from the front to the back, radiator, sub frame, etc…. I can ship. Just let me know what you need and I can price it for you.
All parts in great shape and have been cleaned.
Thanks again
Mike


2014 Kubota RTV-X1120d parts forsale

Rear Wheel Lock cable on 2004 RTV 900

vendredi 10 février 2023

Has anyone used some type of Lever Lock in Place of the Cable (Choke Cable) to hold the Rear Wheel Locked when in use?
Woody


Rear Wheel Lock cable on 2004 RTV 900

Hello, new guy here

Hi All, new member here. Just became the owner of a rtv1100 last month that I believe is a 2008 model. She isn't pretty but she runs like a top. I've been going through the machine a little bit at a time and fixing things. Earlier this week I removed the entire airbox assembly because I had cold air coming from the dash vents but hot air from the defrost. I had a feeling that something was jammed inside and sure enough upon disassembly I found a 2 bottles of hand sanitizer, a glove, a...

Read more


Hello, new guy here

New Kioti NX6010 Problems

jeudi 9 février 2023

I just purchased an NX6010 HST cab (14 hours). It is not the tractor my 14-year-old DK45HST cab is. Yea, it has more horsepower plus major unwanted problems. I was told that the NX had a heavier front axle and was built better than my DK45. Not true. The NX hesitates when it moves forward or back, then jumps rapidly. My buddy was helping me hook up a 3-point counterweight, and I started to creep back, but it hesitated and then jumped. Luckily, he was not between the tractor and the...

Read more


New Kioti NX6010 Problems

?? Question front end nose panel??

Hello everyone,I'm to the point of assembly an when I go to put the plastic nose panel,that has the headlights an all in one piece,(pics below) I only see 2 bolt holes on each side that are in the cab holding this entire piece on? Nothing at all in front or outside at all. Is there something I'm not seing? Seems awful weak to me just having the entire nose panel basically flopping in the wind ,just held on by 4 bolts on the inside. Can someone confirm this? Its the 04 rtv 900.
If this is the...

Read more


?? Question front end nose panel??

B2620 in the Snow

mercredi 8 février 2023

Well, it went from minus 40 the other day to plus 6*C today. Son in law has been plowing the yard with the RTV while I was gone so today I cut some of the base off the driveway. Still impressed with what a little powerhouse that little B is.
And for all the complaints I here about R4's being no good on snow and ice, I have no problem at all with steering or traction and it was melting wet snow and I was cutting down to the ice.


B2620 in the Snow

TC35D Temp Gauge Erratic

Hi
New to this forum. I have a NH TC 35D that has a temp gauge that recently started going to max shortly after starting (sooner than it would have time to heat up ). On occasion a few toggles of the key and it returns to normal. Temp sensor was replaced with no change. Any ideas on aftermarket gauge as factory is nearly $400. Are there resistance measurements that I can check on the gauge or cluster pins?
Thanks in advance.


TC35D Temp Gauge Erratic

What year RTV do you currently own?

mardi 7 février 2023

Another thread got me thinking about the age of members RTV's. Wondering if people still have the old ones or are the new ones more common.
I don't recall when the model years changed so the year selections in the poll may not reflect particular models.
For this poll, it doesn't matter which model you have (900, 1100, X series...).


What year RTV do you currently own?

Frame complete! Floor template made for anyone that needs it!

dimanche 5 février 2023

Ok,my frame is done finally! I made a template for the floor wheel wells,was pretty easy actually,I was able to do it with only one seam! Two sections.i used my flatbed truck as a bender lol.put the metal between my 2x8's on my truck flatbed,an boom! Results in my photos below,an on my YouTube chanel.81deeds72 if interested.
So I'd like to send the template to a administrator here,so if anyone is in need they will be on hand again.i can send a alluminum template,or card board.cardboard is...

Read more


Frame complete! Floor template made for anyone that needs it!

A Note about Side Mirrors (77700-V5059) for X1100C

samedi 4 février 2023

There are a number of threads in which mirrors have been discussed, however this comment is a bit different so I made it a separate comment. I ordered the Kubota side mirrors when I ordered my X1100C. I took delivery in December of 2021. I do like them - but I agree the passenger side mirror is a bit too high, but certainly serviceable for backing up. I was adjusting my mirrors and notice the heads of the phillip head screw were rusty! The captive nuts too, were getting rusty. I don't...

Read more


A Note about Side Mirrors (77700-V5059) for X1100C

EMP Rear Bumper for RTV - Anyone Have This?

vendredi 3 février 2023

Has anyone installed the EMP rear bumper for their RTV?

Looks like it would really protect the tail gate and transmission. But it appears to obscure the tail lights. Anyone have a picture of the finished product?

Thanks


EMP Rear Bumper for RTV - Anyone Have This?

Stupid question

jeudi 2 février 2023

I apoligize already,but being green to these rtv's, how hard should these be to push on flat level ground in neutral? I had a dam hard time even moving mine,had to tow it.im thinking.if its not supposed to be like that, I need to check brakes hanging up mayb? Any thoughts? 04 rtv 900.


Stupid question

In need of 04 kubota rtv 900 rear tailgate

No need to be perfect just useable!
I can't afford a new one for 600$ an searched everywhere for used for a reasonable price anyway.


In need of 04 kubota rtv 900 rear tailgate

Progress!!! My frame repair/ fabrication

Ok.the worst passenger side is finally complete! The front tube at strut is complete on drivers side. Now I need to start the frame on drivers side tommorow!
Before an after pics attached!


Progress!!! My frame repair/ fabrication

Rear tailgate ? 04 rtv 900

Anyone happen to have a rear tailgate for a 04 rtv 900? Does not need to be pretty or shiney! Just atleast able to be used.
I just do not have 600$ for one.i can make something if needed.im just trying to find one first halfway decent.i have searched all other places already before asking here.
Also does anyone here make stickers!? If I make a gate I'd like to put the kubota,an diesel sticker on as well.


Rear tailgate ? 04 rtv 900

Side Kick accessories installed on X series rtv

The XG 850 has some nice accessories that fit the X series rtv . I thought it would be fun to show them installed on the x 900. I have the bed rails and front bed extender plate/ seal installed that work very well. My latest side kick accessory upgrade is the front hood rack. It is kubota's version of the Seizmek rack. I modified the install slightly to clear my wiper blade and it fits great. I think it will be very useful. It has a 75 lb rating. I thought it may block vision but it is...

Read more


Side Kick accessories installed on X series rtv