New Holland 273 Hayliner fluid

jeudi 31 mai 2018

I own a 273 Hayliner. I would like to drain and put in new oil (or grease) but do not know how to check it or what type of fluid to replace it with. Thanks!



New Holland 273 Hayliner fluid

Upgrading Equipment

I need to upgrade some of our hay equipment, mainly our round baler and mower.  I currently use a 20+ year old Kuhn GMD700, but would like to go to a center pivot discbine with around a 12 feet cutting width.  The two main models I have been looking at are a New Holland 312 and a Vermeer MC3700.  As for a baler, I am currently running a New Holland 650, the two models that I have been looking at are a Vermeer 504R Signature and a Claas Variant 360/460. 

 

Has any one used any of these machines?  My hope is to get through this year with the equipment we have, then upgrade over the winter and next spring, I'm just trying to start gather information and looking at the cost to do these upgrades.

 

Thanks



Upgrading Equipment

Burn down before planting

How long does Roundup have to stay on before it will kill.
Just say I sprayed and 4 hours later it came a rain will it kill the weeds

Burn down before planting

Vermeer 554xl packing hay on back side of bottom drum & bale ramp

I have a used 554xl with wide pickup & net.  It is plugging with hay between bottom drum and bale ramp, I don't understand how it can even get hay back there.   I have new bearings put in the bottom drum, new teeth, new cam rollers etc...  According to my parts book it shows that there should be two idler rollers on the bottom of the tail gate, with a bar with a 1/4 bar welded to placed further back in the tailgate, but on my baler the bar is at the end of the tailgate, next to the lower drum, my dealer says that's the right way for that bottom bar to put in, and showed me the safety doc. that explained how to install the bar.  Any one have any suggestions on what is going on. and how to stop this issue.  thanks



Vermeer 554xl packing hay on back side of bottom drum & bale ramp

Esh Tedder

Thinking about getting a second Tedder. Going to look at new four star. My question is does anyone own or use the Esch Tedder. I was told they have a working width of almost 22 feet, on a 4-star. Many of the others are barely at 17 feet total working width. With a 13-foot mower that would come in handy.

Esh Tedder

Agratronix BHT-2 vs Hand Held- Inconsistant Results

mercredi 30 mai 2018

Late last year I installed a BHT-2 moisture meter in my round baler. I didn't have much time to test it out last year. I used it once.  It calibrates correctly and everything appears correct. I baled this weekend with it in hay that was to be wrapped. My gut says hay was 40-60%. Meter showed a few spots at 30% but most of the time it showed 20-25% moisture. Some even showed "Low" which is think is below 14.5%. I knew there was no way this was accurate so I grabbed my handheld Agratronix and probed a bale. Showed on the handheld 45% which is max it will read. Chances are it was more than 45%.

So how can two probes be that far off? The only thing I can think of is the baler unit really doesn't work well on high moisture and is better at the 14-20% range and doesn't accurately display high moisture levels...

Anybody using the BHT-2 for baleage? Does it work?

 



Agratronix BHT-2 vs Hand Held- Inconsistant Results

BC5080... what is this?

mardi 29 mai 2018

Picked up a baler, it has a triangular pan in the feeder just before the bale chamber. I've only seen flat pans there. Anyone familiar with this setup? What's it trying to correct or improve?

Attached Thumbnails

  • C14A892A-1AAE-41B7-8F99-E3144A8176C3.jpeg


BC5080... what is this?