Khun Hay Tedder GF 671

Can anyone tell me where I could fine parts for this old hay tedder. I am looking for the part that get the tines bolted to. It's a four arm tedder with four tines on each gear housing unit. Khun no longer makes replacement parts for this model. I'll even take a used part, I'm not picky as long as I can find the part.



Khun Hay Tedder GF 671

Home Made High Rise Air Intake RTV 900

The other day I removed my air filter (K&N Outer Filter), blew it out, and decided I needed to get my intake higher than the stock setup. Here is a breakdown of the parts that I used. In the first picture is the lower assembly, starting with the curved factory hose attached to the intake on the air filter canister and the parts are listed beginning with that hose:



2" OD x 2 1/8" ID exhaust pipe adapter $3.50

2" PVC Street Elbow $2.27

2" OD x 2" OD exhaust pipe adapter $3.50

2" ID Flexible Exhaust Pipe(6' pc) $28.00



Second picture:



2" ID Flex pipe (used 4')

2" OD x 2" OD exhaust pipe adapter $3.50

2" PVC Street Elbow $2.27

2" PVC pipe (not cut)

2" PVC elbow

2- 2" screw pipe clamps



The items not priced were in my home stock. I used Flexfix tape for class 1 duct to attach and seal all connections. The 2" OD x 2 1/8 ID adapter slipped over the factory hose and note that I cut off 1/2" the smaller end of that adapter. The other adapters fit inside the flex pipe and I used screw clamps at those connections after taping. The metal adapters fit snugly in the PVC fittings and the tape creates a tight seal. The 2" flexible exhaust pipe just fit between the ROPS and the bed without pinching. I used PVC cement to attached the top PVC street elbow to about 13" of 2" PVC pipe.



Cable ties were used generously to secure the pipe and at the very end of the intake I decided to use at PVC "T", instead of a 90 degree elbow, wrapped with fiberglas furnace filter material to keep any flying critters out. Overall, I had a little less than $50 in material, not counting what I had in home stock, plus time and gas to pick up material, and about 1-1/2 hours of labor.



The remaining pictures are the final results. I started up the engine and it seems to run fine.

Attached Images

	2014-08-20 KUBOTA HIGH RISE AIR FILTER 8.20.14 001.jpg (32.9 KB)
	2014-08-20 KUBOTA HIGH RISE AIR FILTER 8.20.14 002.jpg (37.4 KB)
	2014-08-20 KUBOTA HIGH RISE AIR FILTER 8.20.14 003.jpg (64.6 KB)
	2014-08-20 KUBOTA HIGH RISE AIR FILTER 8.20.14 005.jpg (52.9 KB)
	2014-08-20 KUBOTA HIGH RISE AIR FILTER 8.20.14 004.jpg (72.3 KB)

Home Made High Rise Air Intake RTV 900

motorcowl

søges motor cowl til hyperion super chipmunk 70e

Har du sådan et er jeg køber

Mvh Ole kolding mfk

motorcowl

ASW 19/20 fra Traplet

Hej.



Prøver at starte en ny "træ" byggetråd.

Jeg er ny i dette "game" men håber jeg kan følge op efterhånden som byggeriet skrider frem.



Jeg havde egentlig valgt mine vinter bygge projekter men denne ASW19/20 på 3m.fra Traplet sneg sig ind.

På en tur for nylig til England fik jeg kittet med hjem i bilen og dermed uden fragt skader.

Jeg holder meget af at bygge og denne model er helt i træ.

En 3m.passer godt i værksted og bil og er nok pt. nemmere at få flyvende for mig som nybegynder.

Det er min første skala glider projekt og kun det andet byggeprojekt efter mere end 30års pause fra modelflyvning.

Foruden tegning består kittet af en canopy og alle ribber og spanter mm. laser skåret i meget fin kvalitet.

Alle spanter i kroppen skal have 1,5mm balsa på begge sider og der bruges hvid lim ju-hu.



mvh.Jørn:)

ASW 19/20 fra Traplet

Skift af sender modul Graupner MZ 24

Hej



Er der nogen der har erfaring med eller ved om man kan skifte sendermodul i en Graupner MZ 24 til eksempelvis DSMX

Skift af sender modul Graupner MZ 24

Spektrum DX7

Hej

Overvejer at sælge min DX7 da jeg vil have flere kanaler. Er der interesse for at købe en sådan og hvad er den værd i dagens DK?

Spektrum DX7

Help me figure this customer out

Because I sure as hell can't.

A woman rents a stable and land from a rich guy. She is pretty sharp and has all 23 stalls rented. Like me, she hustles all day, lives in tattered rags and drives junk with 100k miles.

She asked me to cut and bale all the property in June and I could keep it all, which I did. She even allowed me to store 8 of the best RB's in a riding arena. Sporadically, she had me deliver straw to her, but she would NOT buy my hay. She would have me go get medium bales from a big local guy i know and deliver them to her. I also bush hogged her paddocks

Sounds pretty good so far, right?

About 3 weeks ago, I stopped by and noticed she ran out of small squares and one of my round bales she was allowing me to store was cut open.

I was all jacked up. I thought "finally she's using my hay". I asked the stable hand if the horses liked it. He said he thought they liked it, but I could easily see it wasn't as good as the hay that I was bringing in from the other guy.

In fact, I think I may have made a mistake allowing her to access it, because now she can probably see it is just bales from the best patch of grass I could find on her property.

I contacted her a few days after she used up 2-3 bales and asked her if she wanted to buy the rest. She did. I got good money for all 8 of them.

Knowing it was average at best hay (really just the best 8 RBs of a natural grass field), I told her I had 10 Orch/Tim mix bales from another field ready for her if she wanted better hay. I also told her they were much better quality.

I stopped back yesterday and the place was filled with someone else's straw and someone else's hay.

I have done everything but shined her floors.

What went wrong????



Help me figure this customer out